欢迎光临锦工风机官方网站。提供优质罗茨鼓风机罗茨风机回转式鼓风机三叶罗茨风机等产品

德国进口罗茨风机总代理_罗茨风机

德国进口罗茨风机总代理_罗茨风机

德国进口罗茨风机总代理:上海进口AERZEN罗茨鼓风机厂家

  上海钰捷机械有限公司是一家致力于为国内外广大用户提供进口罗茨和螺旋鼓风机产品、风机成套机组及技术解决方案的公司。公司凭借高效、体贴的销售团队和强有力的技术实力成为GardnerDenver Aerzen Robuschi授权的风机联盟核心成员,欧美高端品牌成套商,主要业务涵盖了主机、整机、配套件、改造、正品配件、主机维修等。根据您的技术需求及应用场合,我们采用国外先进的选型软件为您提供品质卓越的主机产品及成套机组,上海钰捷将为您的设备提供一站式保姆化服务。

  Aerzen机械制造公司从1868年开始制造罗茨鼓风机,是世界上历史*长和规模*大的风机制造商,也是欧洲市场的技术领先者。强大的技术能力、经验丰富的员工和与客户的不断对话保证了Aerzen和我们的客户始终处于科技发展的前沿。

  德国罗茨鼓风机Delta系列应用简便,连接好送风管道,加上润滑油,接上电源,该款组装好的风机就可以运转了,*大限度的降低了该款风机的安装成本。

  该系列风机有16种规格,吸气流量从30m3/h到15000m3/h,出口压力*高达1000mbar,更高吸气流量的风机请洽询代理商。

德国进口罗茨风机总代理:进口罗茨风机(德国凯森总代理)

  进口罗茨风机(德国凯森总代理)

  我们的罗茨风机来自凯森品牌,我们的罗茨泵在德国工厂生产。

  德国KAYSEN凯森进口罗茨风机概述

  罗茨风机具有中等负载,*风量5709m3/h,*功率为117KW。同步斜齿轮结构使风机具有更低的噪音及平稳的运行状态。重载荷金属支架轴承使风机在较高的载荷工况下依旧保持*的性能表现和更长的寿命。密封采用机械密封结构,确保其密封性更加优秀。该系列风机可以选择水平安装或者垂直安装啦满足不同的工况。

  产品图片

  主要特点:

  风机采用活塞环密封设计能够满足高转速的要求,*转速可达3000rpm,所有与密封面接触的轴端面都经过抛光处理,以减少密封面的磨损,并降低其泄漏风险。摆线式叶轮线性设计能够输送更高压力的气体,*压力可达1.05bar(g)。齿轮材质全部为热处理后的合金钢,分体式齿轮设计更便于安装拆卸。另外特殊的壳体设计,即使在输送高压力气体时也无需水冷。

  主要优点:

  ●轴承的选用较为合理,各轴承的使用寿命均匀,从而延长了风机的寿命

  ●风机油封选用进口氟橡胶材料,耐高温,耐磨,使用寿命机种齐全,可满足不同用户不同用途的需要

  ●风机容积利用率大,容积效率高,且结构紧凑,安装方式灵活多变

  ●叶轮和轴为整体结构且叶轮无磨损,风机性能持久不变,可以长期连续运转

  主要应用:

  ●过滤器逆洗

  ●真空除尘

  ●物料输送

  ●污水曝气

  ●净水厂

  罗茨风机操作注意事项须知

  罗茨风机操作注意事项

  1、KAYSEN罗茨风机运行时做好记录,以便早期发现异常,并给故障原因调查提供有利参数。

  1) 电源电压、运行电流值、频率;

  2) 吐出压力;

  3) 大气温度、吐出温度、轴承部温度;

  4) 振动、噪音;

  5) 润滑油位、油脏污情况等。

  2、KAYSEN罗茨风机流量调整方法:

  流量大小不能通过开关阀门来调整。锦工罗茨风机是容积型压缩机。关闭阀门,压力上升,锦工罗茨风机超负荷运转,易被烧坏。故出口管道的阀门必须完全打开。只能通过调整频率来改变转速从而改变流量和轴功率或增设溢流管道来调整流量。

  3、KAYSEN罗茨风机出口压力表开关应处于长闭状态,只有在检修后试机或需测定压力时才将压力表开关打开。

德国进口罗茨风机总代理:进口罗茨风机(德国进口品牌)品牌:德国凯森KAYSEN品牌

  进口罗茨风机(德国进口品牌)

  德国KAYSEN泵业,德国*水泵品牌,德国十大水泵品牌之一。

  德国凯森泵业中国总代理:营派阀门(上海)有限公司

  德国KAYSEN凯森进口罗茨风机概述

  罗茨风机具有中等负载,*风量5709m3/h,*功率为117KW。同步斜齿轮结构使风机具有更低的噪音及平稳的运行状态。重载荷金属支架轴承使风机在较高的载荷工况下依旧保持*的性能表现和更长的寿命。密封采用机械密封结构,确保其密封性更加优秀。该系列风机可以选择水平安装或者垂直安装啦满足不同的工况。

  主要特点:

  风机采用活塞环密封设计能够满足高转速的要求,*转速可达3000rpm,所有与密封面接触的轴端面都经过抛光处理,以减少密封面的磨损,并降低其泄漏风险。摆线式叶轮线性设计能够输送更高压力的气体,*压力可达1.05bar(g)。齿轮材质全部为热处理后的合金钢,分体式齿轮设计更便于安装拆卸。另外特殊的壳体设计,即使在输送高压力气体时也无需水冷。

  KAYSEN罗茨风机图片展示:

  主要优点:

  ●轴承的选用较为合理,各轴承的使用寿命均匀,从而延长了风机的寿命

  ●风机油封选用进口氟橡胶材料,耐高温,耐磨,使用寿命机种齐全,可满足不同用户不同用途的需要

  ●风机容积利用率大,容积效率高,且结构紧凑,安装方式灵活多变

  ●叶轮和轴为整体结构且叶轮无磨损,风机性能持久不变,可以长期连续运转

  主要应用:

  ●过滤器逆洗

  ●真空除尘

  ●物料输送

  ●污水曝气

  ●净水厂

  KAYSEN的售后解决方案经过深思熟虑并面向客户。时间和精力的有效投资有助于保持泵的长期可靠运行。我们的服务理念提供*的服务,但仍符合客户的经济利益。

  该服务可以根据应用程序和客户的具体要求进行组合和访问。

  这包括:

  ●现场维修

  ● 工厂修理

  ● 预防性维护

  ●培训客户的人员

  ● 设置和修改系统

  ●调试

  ●通过电话远程诊断

  ●维护和维护协议

  ● 修订服务

  KAYSEN的特殊修改服务为即将到来的修订,现代化和大修提供全面的帮助。

  ● 评估缺陷和原因解释

  ● 制定维修计划

  ●将传统操作系统转换为频率控制操作的建议

  ● 性能测试

  关于德国KAYSEN

  位于德国Schw?bischGmünd的凯森Kaysen泵业有限公司是*的各种流体水泵和隔膜泵制造商之一。60多年来,凯森以“德国制造”的可靠性和质量达到了*标准。凭借我们全面的产品组合,我们支持世界各地的客户成功掌握供水,采矿,工业,化工,造纸,电力,食品,制药,污水和海上行业的苛刻抽水任务。作为上述领域创新技术的*供应商,我们是液体需要安全,高效和经济运输的*合作伙伴。

  德国凯森始终坚持“重质量,讲信誉”为宗旨。产品现畅销全国各地,并已逐步开发海外市场。公司多次被评为“重合同讲信用”企业,深得用户的信赖和广泛的赞誉。

  The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world’s leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of “Made in Germany”. With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,

  Germany Kaysen always adhere to the “quality, stresses credibility” for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as “the contract with the letter” business, won the trust of users and extensive praise.

德国进口罗茨风机总代理:进口罗茨风机(总代理)

  进口罗茨风机(总代理)

  KAYSEN PUMP

  罗茨风机选型指南

  按类型、型号进行选择

  罗茨风机可分为多种类型,例如材质坚硬、耐磨且具有一定防腐蚀效果的罗茨风机,该类型的罗茨风机一般适用于发电站、发电厂等场所;具有防爆功能的罗茨风机一般适用于产生易燃易爆气体的场所;而通风性能好、排气速度快的罗茨风机则比较适用于井底、隧道等通风性较差的场所。罗茨风机的型号由字母与数字组成,一般具有固定含义,可根据自身需求进行选择。

  按流量、转速进行选择

  罗茨风机的流量有着其自身的计算公式,根据公式来计算该罗茨风机的流量即可得到准确的流量系数。转速的选择则是根据叶轮的半径、大小而决定的。

  按风压、效率进行选择

  风压是气体流经风叶时产生的压力差值,可根据空气密度、压力系数等可测数据进行推算。不同的环境需要不同风压的罗茨风机,因此要根据自身环境进行测量、推算,从而得到风压的值,再根据风压值选择合适的罗茨鼓风机。罗茨风机的效率也是需要根据罗茨风机的风叶形状、系数进行计算的。除此之外,罗茨风机的电功率的大小也决定了罗茨风机的工作效率。

  Roots Fan Selection Guide

  Select by type and model

  德国KAYSEN罗茨风机优点:

  ●轴承的选用较为合理,各轴承的使用寿命均匀,从而延长了风机的寿命

  ●风机油封选用进口氟橡胶材料,耐高温,耐磨,使用寿命机种齐全,可满足不同用户不同用途的需要

  ●风机容积利用率大,容积效率高,且结构紧凑,安装方式灵活多变

  ●叶轮和轴为整体结构且叶轮无磨损,风机性能持久不变,可以长期连续运转

  Roots fan advantages

  ● The selection of bearings is more reasonable, and the service life of each bearing is even, which prolongs the life of the fan.

  ● The fan oil seal is made of imported fluoroelastomer material, which is resistant to high temperature and aJGRasion and has a complete service life.

  ● Large volume utilization rate, high volume efficiency, compact structure and flexible installation

  ●The impeller and shaft are of integral structure and there is no wear on the impeller. The fan performance is durable and can be continuously operated for a long time.

  德国KAYEN罗茨风机使用的注意事项:

  ●起动前的准备:

  检查各部位紧固情况,检查进、排气管和机组在基础上的安装质量。

  按照电动机铭牌要求接通电源,确认电动机转向正确后再与鼓风机接通,鼓风机严禁反转,电动机功率≥22KW时,应采用降压启动装置。

  向轴承油箱和齿轮油箱内加入润滑油,油量应加到圆形油标的中线。

  全部打开进排气管道上阀门,用手盘动鼓风机主动轴,应灵活无阻滞,仔细倾听有无不正常响声。

  ●空负荷试运转:

  空负荷试运转是指鼓风机在进排气口阀门全部打开情况下进行的试运转,新安装或大修后的鼓风机都应该空负荷试运转,持续时间不少于30分钟,(排气出口可采用放空装置),靠近风机出口处,一定要安装放空阀,风机试运转后,慢慢关掉放空阀,请按铭牌上的压力使用,严禁超压使用。

  试运转时应注意鼓风机有无不正常的撞击、摩擦等响声,各部位不允许有过高的温度,不正常的气味或冒烟现象,还应检查轴承处振动是否正常,如有上述现象,应立即停机,查明原因,排除故障。

  ●正常带负荷持续运转:

  经试运转良好的机组,方可带负荷持续运转,此时逐步缓慢地调节阀门,直到满负荷,切不可一次突然升压到满负荷,也不允许超负荷运转,以免损坏机组。

  正常运转时油箱内用普通机油润滑时,机油温度一般不应高于65C°。轴承部位在X、Y、Z三个方向的振动速度均方根值(有效值)应不大于11.2mm/S。

  Precautions for using roots fans

  ●Preparation before starting:

  Check the tightening of each part, and check the installation quality of the intake and exhaust pipes and the unit on the foundation.

  Connect the power supply according to the motor nameplate, and confirm that the motor is turning correctly before connecting it to the blower. The blower is strictly prohibited to reverse. When the motor power is ≥ 22KW, a step-down starting device should be used.

  Add luJGRicating oil to the bearing oil tank and gear oil tank, and the oil volume should be added to the center line of the round oil gauge.

  Fully open the valves on the inlet and exhaust pipes, and move the active shaft of the blower by hand. It should be flexible and non-blocking. Listen carefully for abnormal sounds.

  ● No-load test run:

  No-load test run refers to the test run of the blower with all the inlet and exhaust valves open. Newly installed or overhauled blowers should be run at no load for a duration of not less than 30 minutes. (Exhaust outlets can be used Vent device), near the fan outlet, be sure to install a vent valve. After the fan is commissioned, slowly turn off the vent valve. Use it according to the pressure on the nameplate. Overpressure is strictly prohibited.

  During the test run, pay attention to the blower for abnormal impact, friction and other sounds. Excessive temperature, abnormal odor or smoke should not be allowed in each part. Also check whether the viJGRation at the bearing is normal. Shut down immediately, find out the cause, and troubleshoot.

  ●Continuous operation under normal load:

  Only after the well-tested unit can continue to run with load, at this time slowly adjust the valve until it is fully loaded. Never suddenly increase the pressure to full load at one time, and do not allow overload operation to avoid damage to the unit.

  When the oil tank is luJGRicated with ordinary oil during normal operation, the oil temperature should generally not be higher than 65C °. The root-mean-square value (effective value) of the viJGRation velocity of the bearing part in the three directions of X, Y and Z should not be greater than 11.2mm / S.

  凯森的承诺

  服务伴随永远

  无论在您购买前或是购买后,我们会坚持为你提供优质的服务。购买前我们可以提供专业优质的购买咨询服务、设备设计和选型建议等服务;购买后,我们可以提供安装、安装指导顾问式的服务,保证产品可以顺利安装使用;若您使用过程中有任何疑问,我们将会第一时间给你提供专业的解答和帮助!

  快速高效的服务

  在整个德国、欧洲和中国大部分城市可以提供快速的现场支持。我们的经销商都是具有泵相关技术服务能力的公司,同时,凯森的工作人员都定期组织安装、故障处理和维护保养等知识的学习,保证工作人员都可以快速高效的处理问题。

  Kaysen Promise

  Service accompanied forever

  No matter before or after you buy, we will insist on providing you with excellent service. Before purchase, we can provide professional and high-quality purchase consulting services, equipment design, and selection recommendations. After purchase, we can provide installation, installation guidance and consulting services to ensure that the product can be installed and used smoothly. If you have any Questions, we will provide you with professional answers and help as soon as possible!

  Fast and efficient service

  Fast on-site support is available throughout most cities in Germany, Europe and China. Our distributors are companies with pump-related technical service capabilities. At the same time, Kasen staff regularly organizes learning of installation, troubleshooting and maintenance to ensure that staff can deal with problems quickly and efficiently.

  进口罗茨风机(总代理)

罗茨鼓风机哪里好 万豪罗茨鼓风机 优质高压罗茨鼓风机 罗茨鼓风机专用油

山东锦工有限公司
地址:山东省章丘市经济开发区
电话:0531-83825699
传真:0531-83211205
24小时销售服务电话:15066131928


上一篇:
下一篇:
锦工最受信赖的罗茨风机回转风机品牌
版权所有:Copright © www.bestblower.com 山东锦工有限公司 鲁ICP备11005584号-5 2016   地址:山东省章丘市相公工业园
电话:0531-83825699传真:0531-83211205 E-mail: sdroo@163.com 网站地图
罗茨风机咨询电话